Fort Wayne, Indiana
As a Fort Wayne commercial roof repair contractor, we find where water gets in and fix the drain, seam, flashing, or panel causing it.
Most Fort Wayne commercial roof repair calls end with a fix to one area. Moisture readings show us when a roof needs more than that.
What We Do
Fits a roof where damage stays in one area and the rest of the membrane or panels still hold.
We Say So Up Front
Becomes the better call once water and wear have spread past what patches can hold.
Five steps, in this order, on every roof we repair. Each one answers a question before money goes into materials.
We cover the whole surface, including seams, curbs, drains, parapets, and penetrations, and look at the ceiling from inside where water shows. The leak you called about is rarely the only weak detail.
Meter readings and a core cut where needed show how far water has traveled into the insulation. That sets the size of the cut-out before anyone quotes a patch.
Photos and a short list split the work into what needs fixing now, what can wait a season, and what keeps causing the leak. You decide the scope.
TPO gets welded patches, EPDM gets primed tape, metal laps get butyl and new fasteners, and wet insulation comes out first. Mismatched materials are the reason many patches fail early.
Welds are probed, laps are checked for tight fasteners, and drains are run with water where we can. Finished work goes into the photo record with the rest.
Pick the one that matches what you are seeing. Each card names the symptom that usually brings an owner to that repair.
Built for TPO, EPDM, built-up, and modified bitumen roofs on offices, stores, and warehouses where drains, seams, and blisters are letting water into the insulation.
Typical Repairs
Covers exposed-fastener and standing-seam roofs on shops, plants, and storage buildings, where screws back out, laps open, and trim rusts long before the panels give out.
Typical Repairs
Starts inside, at the stain, and follows the water uphill to the opening on the roof. Owners call here when they know where it drips but not where it enters.
Typical Repairs
Plant roofs with exhaust stacks, skylights, residue, and heavy foot traffic, repaired in phases so production lines and controlled rooms below stay dry.
Typical Repairs
Call and describe where it shows inside. We can cover the opening while the permanent repair is planned.
The goal is a roof that stops taking on water at the details that failed. Here is what that looks like on a typical repair.
Before The Repair
After The Repair
These six conditions account for most of the leaks we trace. Each one has a repair that matches it.
Leaves and grit clog the strainer, water backs up, and the membrane at the drain flashing wears out first.
Heat, cold, and foot traffic pull lapped seams apart a little at a time until water wicks under the membrane.
Panels expand and contract daily, which loosens screws and cracks rubber washers along every lap on a metal roof.
Open coping joints and base flashing pulled off the wall let water in above the roof surface, where it runs down inside.
Spring hail can puncture single-ply membrane, crack metal seams, and crush the insulation boards hidden underneath.
Frozen drains and scuppers hold back snowmelt until it rises over flashing heights or seeps through laps.
Plants, warehouses, metal shops, and storefronts in these towns are where we repair roofs most. Elsewhere? Call us or send us a message.
Parapet and coping leaks on older downtown buildings get most of the calls.
Huntington commercial roof repair →Drains, long seams, and dock canopy flashing on warehouse roofs.
New Haven commercial roof repair →Office and storefront roofs repaired while the doors stay open.
Auburn commercial roof repair →Metal shop roofs with backed-out screws, open laps, and worn ridge caps.
Huntertown commercial roof repair →Wind and hail damage photographed first, then covered and fixed.
Bluffton commercial roof repair →Your lease answers it, usually in the repair and maintenance clauses read together. Net leases often put routine upkeep on the tenant and structure and replacement on the landlord.
We write up what failed and why, with photos, so both sides can match the repair to the lease language.
Often, yes. If the wet area is contained and the surrounding membrane or panels hold, we cut out the damage, replace it, and tie the new section into the old with compatible materials. Wide wet readings change that answer, and we tell you before work starts.
A full walk of the surface, a look at every drain, curb, seam, and flashing, and a check of the ceiling from inside where leaks show. Moisture readings or a core cut confirm wet insulation. You get photos and a ranked repair list.
Documentation comes first: photos and measurements of each bruise, puncture, and dent, which insurers usually ask for. Then punctured membrane gets patched or replaced in sections, cracked metal seams get resealed, and damaged vents and flashings get replaced after we check for crushed insulation.
Many repairs can. Fasteners, metal flashing, and some membrane patches go on in the cold, and temporary covers stop an active leak. Sealants and adhesives have temperature limits, so part of the permanent work waits for a milder day. Snow is cleared from the work area first.
It turns on the scope. A small patch is handled differently from replacing deck, insulation, or a large area, and the Allen County Building Department makes that call. We check with the department before any larger repair begins.
Tell us where the water shows and what the roof is made of. We will set up a roof walk and a moisture check.